Showing 2780–2790 of 10097 results

Aluminum flanged construction, holds two 4-1/2” fans in 3 spacesFan panels accommodate all standard 4-1/2” fans. 3 rackspaces (5-1/4”) high, they are made from 16-gauge flanged aluminum. Offered in a black textured powder coat finish.Fan panel holds two 4-1/2” fans in three rackspacesAluminum flanged constructionBlack powder coat finish

Freestanding, Rack-independent system with the flexibility to maximize efficiency and capacity from the core to the edge for raised floor and slab data centers. Adaptable to hot and cold aisle containment, the Vertiv Aisle Containment system allows you to deploy containment before or after racks are installed to simplify installation and speed deployment of new data center equipment.

Convenient and useful solutions that solve everyday problems are a major focus at RAM. If you find that tools are not always the most convenient way to adjust your laptop retaining arms, you're going to love this easy to install knob kit for the RAM Tough-Tray. This kit is ideal for trays that hold laptops of varying size or if you simply need to quickly move a retaining arm out of the way to access a port or drive. Quick and simple to adjust without the use of tools, this useful product is just another high quality RAM accessory offered for the RAM Tough-Tray.

The Vaddio Extreme USB 2.0 Extenders provide a complete plenum extension solution for situations where your high-bandwidth USB 2.0 device (like a camera or other av source) cannot be installed near the computer it needs to connect to. The system includes a transmit (TX) or remote device side and a receive (RX) or Host PC side and extends full-bandwidth USB 2.0 high speed and USB 1.1 devices up to 328 ft. (100m) over Cat-5e or better cable.

Commercial/institutional functionality plus attractive, durable design. Installers say low VGA connector makes easier installation.Add the finishing touch to audio/video installations with a decorative feed-through wall plate. This wall plate is stamped from sturdy 20 gauge stainless steel, and is designed to mount in standard electrical boxes or mud rings. The thick stainless steel composition provides better protection than plastic wall plates in commercial environments where constant wear and tear causes damage.Feed-through connectors and identification markings make this wall plate simple to install and easy to connect equipment. Furthermore, it is compatible with any existing wiring network. The single gang design offers connectors for HD15, 3.5mm stereo audio, composite video, and left/right audio, all in one wall plate. Feed-through connectors are designed to offer lossless signal transfer and maximum insertions for a lifetime of service. The low placement of the HD15 connector in this configuration enhances cable-routing flexibility during installation. Mounting hardware included.

This RAM-103U-D-2461 consists of a 1.5" rubber ball, connected to a 3.625" square plate with a 75mm X 75mm VESA hole pattern and LONG length double socket arm. The rubber ball is positioned 0.88" from the center of one edge. The double socket arm will attach to all RAM 1.5" dia. ball bases.

Freestanding, Rack-independent system with the flexibility to maximize efficiency and capacity from the core to the edge for raised floor and slab data centers. Adaptable to hot and cold aisle containment, the Vertiv Aisle Containment system allows you to deploy containment before or after racks are installed to simplify installation and speed deployment of new data center equipment.

The RAM-137BU, universal mounting plate, consists of a 1.5" diameter rubber ball, connected at right angles to a flat 3" x 11" rectangular plate. The plate contains different combinations of pre-drilled holes which will match up to many electronic devices and mounts, including Marine GPS, CB Radios, Ham Radios, Gimbal Brackets and more.

Vent blockers are used to prevent the recirculation of hot air between top-mount fans and nearby vent openings. Vent blockers should be placed over the enclosure’s vents located on the upper front of the enclosure, upper sides, and upper rear door (depending on enclosure). This will ensure that heated enclosure air will be forced out through the top-mounted exhaust fans instead of re-circulating, keeping equipment cool.